![]() I record with "Windows Sound Recorder" program or "Audacity". ![]() Then I set the "Listen" tab in the mic settings so that I monitor my sound through my laptop speakers. Then open up the "Recording Devices" settings and set the levels accordingly, I didn't need to use the boost, and my mic level ended up around +18db for the test clip I made. Plug the Stereo RCA into the back of the SJ and the 1/8th jack into the Mic input on your computer. I use just the preamp section (such as the Drive, Volume, Tone Stack, Effects and Reverb) to get my levels the way I want them. ![]() This setting is the 8th one down in the settings section. Sometimes it’s more difficult to find a 3.5mm to RCA cable than it is a normal RCA cable, so that might affect your decision. Don’t think it makes any difference at all. according to my setups i cannot hear any difference. First get amp the setting "Output Routing" to "Normal", there's two choices Normal or Performance. The Hifiberry has two RCA connectors and the Wolfson a 3.5 mm jack stereo line output. I've just got done hooking it up again and it still works fine. I'm using a Vaio Laptop (6 years old) with Windows 7. The other end of the RCA cable went into this little portable CRT tv I have that can also accept composite video input.If I understand you correctly you have a combined Mic/Headphone Jack? My computer uses seperate jacks so I don't have that experience yet, but I may still be able to help you, gonna have to research it. In the second picture, you can see the white alligator clip connected to the signal pin of an RCA connector and the black clip connected to the grounding part of the RCA connector. Many audio systems have tape ins and outs so you can connect up your computer through these to use it as a tape recorder as well as a sound source. I just chose HDMI since connecting to that case would make the black alligator clip face the same direction as the white one (I like symmetry :p ). You then connect the RCA jack stereo ends to the main audio output of your stereo receiver, if it has one, or to a routable output such as one of the 'tape' output jacks. You can use anything that is grounded on the Pi (HDMI casing, ethernet casing, USB casing, gpio ground, circuit board ground, etc) as long as it is connected to ground. It is actually used as a ground connection for the video signal since composite video uses one signal wire and one ground wire. ![]() Some people were asking why I had a black alligator clip connected to the HDMI casing, and they speculated that it was for static discharge purposes or something. General Discussion - does splitting rcas/pre outs do anything to the signal - my deck has one preout and I will be using a 4 channel amp that has 4 rca. Here is also where I got a few questions. Here you can see a picture of my Raspberry Pi 2 with an alligator clip in the audio jack. BUT!!! In the rare event that your Raspberry Pi does get damaged by shorting video with something else, it is IN NO WAY MY FAULT since I am not forcing you to do this (and I see no reason why anything would get damaged). Shorting with ground should not damage the Raspberry Pi since a standard TRS (yes, only one R this time) will short the video and ground, so safety measures have been implemented to prevent damage. It's very close to the opening so it doesn't even have to go in very far.īut word of caution, if you do put it too far in, then you won't get any video since it might short with ground or an audio pin. This makes wiring it up very easy since all you have to do is connect an alligator clip to that little pin. It is close to the outside since on the previous diagram, the video pin on the male jack was also in the same place. This little prong is the video output pin. If you take a look at the TRRS jack of the Raspberry Pi 2, you'll see that you can see a little metal prong which is very close to the opening of the jack.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |